ZIMFLEX 901 Polyester Polyurethane Hose — Material Safety Data Sheet

Nov 10, 2026

Leave a message

Section 1 - Identification of the Product and Company

Product name: Polyester-based polyurethane hose (trade name ZIMFLEX 901)

Product type: Spiral-wound hose made of thermoplastic polyurethane elastomer (TPU, polyester type / ESTER PU), a polymer article - not a hazardous chemical

Recommended uses: Woodworking dust extraction, pneumatic conveying of abrasive powders/granules, oily-media fluid lines - applications where abrasion and oil resistance are the primary requirements

Manufacturer: ZIMFLEX INNOVATION TECHNOLOGY (JIAXING) CO., LTD.

Emergency phone: 400 680 7908 (weekdays 8:30–17:30); in emergencies dial 119 / 120 (China)

Section 2 - Hazards Identification

GHS classification: This product is a solid polymer article, stable at ambient temperature. It is not listed in the Catalogue of Hazardous Chemicals (2015) and carries no GHS hazard classification.

Hazard description:

Ambient state: Chemically stable; no acute health hazard in normal use; no dust or volatile irritants.

Hot hazards: Softens and melts above approx. 190 °C; contact with molten polymer causes thermal burns, and the melt adheres to skin and cannot be removed immediately.

Fire hazards: Combustible solid. Thermal decomposition (>250 °C) and combustion release carbon monoxide, carbon dioxide, nitrogen oxides, traces of hydrogen cyanide (HCN) and aldehydes - irritant/toxic smoke.

Mechanical hazards: Cutting or grinding may generate polymer chips; eye contact may cause mechanical irritation.

Environmental hazards: Not readily biodegradable; polyester segments can be slowly degraded by microorganisms in warm, humid environments; bulk disposal constitutes persistent solid waste.

GHS label elements: No signal word, no pictograms; packages should be marked "Keep away from fire".

Section 3 - Composition / Information on Ingredients

Component

Chemical name

CAS No.

Mass fraction

Function

Base resin

Polyester-type TPU (PBA(PEA)/MDI/BDO system)

9009-54-5 (polyurethane class)

94–98%

Hose wall material; ester soft segments confer excellent abrasion and oil resistance

Hydrolysis stabilizer

Polycarbodiimide

-

0.5–1.5%

Scavenges hydrolysis-generated carboxylic acids; essential for ester grades

UV stabilizer

Hindered amine light stabilizer (HALS)

-

0–0.5%

Delays outdoor yellowing

Colorant

Inorganic/organic pigments (absent in clear grades)

-

0–2%

Identification color

Free from: Phthalate plasticizers, halogenated flame retardants, asbestos, heavy-metal stabilizers.

Section 4 - First-Aid Measures

Skin contact: For burns from molten polymer, do NOT peel off the solidified polymer stuck to the skin; cool immediately with copious cold water for at least 15 minutes and seek medical attention.

Eye contact: Flush with eyewash or clean water for 15 minutes; seek medical care if foreign-body sensation persists.

Inhalation: Move to fresh air after exposure to combustion or decomposition fumes; administer oxygen and seek medical care if breathing is difficult.

Ingestion: Ingestion of hose fragments is unlikely; seek medical advice if discomfort occurs.

Section 5 - Fire-Fighting Measures

Extinguishing media: Water fog/spray (preferred, also for cooling), dry chemical, CO2 and foam are all suitable.

Specific hazards: Moderate flame spread; smoldering releases dense, irritant and toxic smoke.

Protective actions for firefighters: Wear self-contained positive-pressure breathing apparatus (SCBA); remove adjacent ignition sources and cool unburned hose coils.

Section 6 - Accidental Release Measures

No chemical release is possible from a hose article. Collect offcuts and chips from breakage or cutting and dispose of per Section 13; prevent scattered debris from creating slip hazards. For oil leaks from attached brass/stainless-steel fittings, follow the metal-part oil-spill procedure.

Section 7 - Handling and Storage

Handling: Use sharp blades for cutting and wear cut-resistant gloves; keep away from heat sources above 190 °C; no open flames or smoking in the work area.

Assembly: Crimp fittings strictly per the manufacturer's selection manual (fitting type and crimp dimensions) to prevent blow-off injuries.

Storage:The polyester type is sensitive to heat and humidity - store in a dry warehouse (≤60% RH) at 5–30 °C, away from direct sunlight, ozone sources and damp floors; store coils flat or suspended, ≥1 m from heat sources; use within 18 months (despite the hydrolysis stabilizer, prolonged warm-humid storage still causes gradual hydrolytic embrittlement).

Incompatibilities: Strong oxidizers (fuming nitric acid, concentrated hydrogen peroxide, etc.); strong acids/bases; prolonged contact with hot water/steam (accelerates ester hydrolysis).

Section 8 - Exposure Controls / Personal Protection

Occupational exposure limits: No dust and no specific limits for the finished article; fume from hot cutting should be controlled to a total dust benchmark of ≤8 mg/m³.

PPE: No special protection required in normal use; wear safety goggles and cut-resistant gloves when cutting/grinding; heat-insulating gloves and respiratory protection for hot-work or burning operations.

Section 9 - Physical and Chemical Properties

Property

Value / Description

Appearance & odor

Cylindrical spiral-wound hose, transparent or natural color; slight ester odor

Base material

Polyester TPU (PBA/PEA soft segments + MDI hard segments)

Density

1.18–1.22 g/cm³

Hardness

Shore A/D approx. 95A–55D

Service temperature

−35 °C to +80 °C (short-term +100 °C)

Softening/melting point

Approx. 190–220 °C

Decomposition temperature

>250 °C

Auto-ignition temperature

Approx. 400 °C

Solubility

Insoluble in water; swells in strongly polar solvents (DMF, NMP)

Abrasion resistance

Excellent (highly polar ester segments); approx. 10× that of PVC

Oil resistance

Excellent (low volume change per ASTM D471 reference oils)

Hydrolysis resistance

Moderate - lower than the polyether type (906S); protected by hydrolysis stabilizer in warm-humid service

Volume resistivity

Approx. 1012 Ω·cm (conductive grades: 103–106)

Section 10 - Stability and Reactivity

Stability: Chemically and dimensionally stable at ambient temperature and pressure; ester bonds hydrolyze slowly in warm-humid environments, retarded by the polycarbodiimide stabilizer.

Conditions to avoid: Sustained heat >190 °C, open flame, prolonged direct UV exposure, long-term warm-humid storage, high-energy sparks (non-conductive grades).

Incompatible materials: Strong oxidizers, concentrated nitric acid, concentrated sulfuric acid, strong bases (saponify ester bonds).

Hazardous decomposition products: CO, CO2, NOx, HCN (incomplete combustion), aldehydes, terephthalate-type fragments (deep pyrolysis).

Polymerization hazard: None (finished high polymer; no reactive residual monomers).

Section 11 - Toxicological Information

No acute toxicity classification is available for the finished TPU article (rat oral LD50 >2000 mg/kg by analogy with similar polymers); no classification for skin sensitization, carcinogenicity or reproductive toxicity. HCN in thermal-decomposition fumes is the principal toxicological risk. No full toxicological testing has been performed on this article.

Section 12 - Ecological Information

Not readily biodegradable; polyester segments can be slowly hydrolyzed by microorganisms (esterase activity) in warm-humid soil/compost, yet the article remains persistent waste.

Incomplete combustion generates CO2; recycling is recommended (TPU can be mechanically and chemically recycled).

Section 13 - Disposal Considerations

Preferably send to TPU recyclers for material recovery; dispose of waste offcuts as general industrial solid waste (non-hazardous) via licensed contractors.

Do not mix with household waste or burn in the open.

Section 14 - Transport Information

UN number: None (non-dangerous goods); transport marking: general cargo.

Packaging: Carton/woven-bag coils; protect from sharp objects, direct sunshine and rain; keep dry in transit.

Sea/air freight: Not regulated by IMO or IATA.

Section 15 - Regulatory Information

Regulations on the Safety Management of Hazardous Chemicals (State Council Decree No. 645) - not applicable to this article.

GB/T 16483-2008 and GB/T 17519-2013 (SDS preparation standards).

Law of the PRC on the Prevention and Control of Environmental Pollution by Solid Waste (disposal).

Export to the EU: REACH (SVHC) declarations; food-contact uses require food-grade grades assessed to GB 4806.7-2016 / (EU) No 10/2011.

Section 16 - Other Information

This SDS is based on current knowledge and a typical formulation; batch variations are governed by the officially issued version; review cycle: 24 months.

Users should verify suitability for their own application (especially warm-humid environments); this document does not constitute a warranty of quality.

Selection principle vs. 906S (polyether type): choose 901 for abrasion/oil resistance in dry conditions; choose 906S for hydrolysis resistance, low temperature or food contact.

Abbreviations: TPU = thermoplastic polyurethane; PBA = poly(butylene adipate) glycol; PEA = poly(ethylene adipate) glycol; MDI = 4,4'-diphenylmethane diisocyanate; BDO = 1,4-butanediol.

Send Inquiry