Section 1 - Identification of the Product and Company
Product name: Polyester-based polyurethane hose (trade name ZIMFLEX 906S)
Product type: Hose made of thermoplastic polyurethane elastomer (TPU, polyester type / ESTER PU), a polymer article - not a hazardous chemical
Recommended uses: Woodworking dust extraction, pneumatic conveying of abrasive powders/granules, oily-media fluid lines, and applications requiring static grounding (conductive grade 906S-X available)
Manufacturer: ZIMFLEX INNOVATION TECHNOLOGY (JIAXING) CO., LTD.
Emergency phone: 400 680 7908 (weekdays 8:30–17:30); in emergencies dial 119 / 120 (China)
Section 2 - Hazards Identification
GHS classification: This product is a solid polymer article, stable at ambient temperature. It is not listed in the Catalogue of Hazardous Chemicals (2015) and carries no GHS hazard classification.
Hazard description:
Ambient state: Chemically stable; no acute health hazard in normal use; no dust or volatile irritants.
Hot hazards: Softens and melts above approx. 190 °C; contact with molten polymer causes thermal burns, and the melt adheres to skin and cannot be removed immediately.
Fire hazards: Combustible solid. Thermal decomposition (>250 °C) and combustion release carbon monoxide, carbon dioxide, nitrogen oxides, traces of hydrogen cyanide (HCN) and aldehydes - irritant/toxic smoke.
Mechanical hazards: Cutting or grinding may generate polymer chips; eye contact may cause mechanical irritation.
Environmental hazards: Not readily biodegradable; polyester segments can be slowly degraded by microorganisms in warm, humid environments; bulk disposal constitutes persistent solid waste.
GHS label elements: No signal word, no pictograms; packages should be marked "Keep away from fire".
Section 3 - Composition / Information on Ingredients
|
Component |
Chemical name |
CAS No. |
Mass fraction |
Function |
|
Base resin |
Polyester-type TPU (PBA(PEA)/MDI/BDO system) |
9009-54-5 (polyurethane class) |
94–98% |
Hose wall material; ester soft segments confer excellent abrasion and oil resistance |
|
Hydrolysis stabilizer |
Polycarbodiimide |
- |
0.5–1.5% |
Scavenges hydrolysis-generated carboxylic acids; essential for ester grades |
|
Antistatic agent |
Conductive carbon black / ionic type (906S-X only) |
- |
3–8% |
Lowers surface resistance to 10³–10⁶ Ω |
|
UV stabilizer |
Hindered amine light stabilizer (HALS) |
- |
0–0.5% |
Delays outdoor yellowing |
|
Colorant |
Inorganic/organic pigments (absent in clear grades) |
- |
0–2% |
Identification color |
Free from: Phthalate plasticizers, halogenated flame retardants, asbestos, heavy-metal stabilizers.
Section 4 - First-Aid Measures
Skin contact: For burns from molten polymer, do NOT peel off the solidified polymer stuck to the skin; cool immediately with copious cold water for at least 15 minutes and seek medical attention.
Eye contact: Flush with eyewash or clean water for 15 minutes; seek medical care if foreign-body sensation persists.
Inhalation: Move to fresh air after exposure to combustion or decomposition fumes; administer oxygen and seek medical care if breathing is difficult.
Ingestion: Ingestion of hose fragments is unlikely; seek medical advice if discomfort occurs.
Section 5 - Fire-Fighting Measures
Extinguishing media: Water fog/spray (preferred, also for cooling), dry chemical, CO₂ and foam are all suitable.
Specific hazards: Moderate flame spread; smoldering releases dense, irritant and toxic smoke.
Protective actions for firefighters: Wear self-contained positive-pressure breathing apparatus (SCBA); remove adjacent ignition sources and cool unburned hose coils. The carbon-black-filled 906S-X leaves conductive dust after burning - clean up with dust-work precautions.
Section 6 - Accidental Release Measures
No chemical release is possible from a hose article. Collect offcuts and chips from breakage or cutting and dispose of per Section 13; prevent scattered debris from creating slip hazards. For oil leaks from attached brass/stainless-steel fittings, follow the metal-part oil-spill procedure.
Section 7 - Handling and Storage
Handling: Use sharp blades for cutting and wear cut-resistant gloves; keep away from heat sources above 190 °C; no open flames or smoking in the work area.
Assembly: Crimp fittings strictly per the manufacturer's selection manual (fitting type and crimp dimensions) to prevent blow-off injuries.
Storage: The polyester type is sensitive to heat and humidity - store in a dry warehouse (≤60% RH) at 5–30 °C, away from direct sunlight, ozone sources and damp floors; store coils flat or suspended, ≥1 m from heat sources; use within 18 months (despite the hydrolysis stabilizer, prolonged warm-humid storage still causes gradual hydrolytic embrittlement).
Incompatibilities: Strong oxidizers (fuming nitric acid, concentrated hydrogen peroxide, etc.); strong acids/bases; prolonged contact with hot water/steam (accelerates ester hydrolysis).
Section 8 - Exposure Controls / Personal Protection
Occupational exposure limits: No dust and no specific limits for the finished article; fume from hot cutting should be controlled to a total dust benchmark of ≤8 mg/m³; carbon-black dust from cutting the conductive grade should be controlled per the carbon-black total dust limit.
PPE: No special protection required in normal use; wear safety goggles and cut-resistant gloves when cutting/grinding; heat-insulating gloves and respiratory protection for hot-work or burning operations.
Section 9 - Physical and Chemical Properties
|
Property |
Value / Description |
|
Appearance & odor |
Cylindrical (corrugated / smooth-bore) hose, transparent, natural or black (conductive grade); slight ester odor |
|
Base material |
Polyester TPU (PBA/PEA soft segments + MDI hard segments) |
|
Density |
1.18–1.22 g/cm³ |
|
Hardness |
Shore A/D approx. 95A–55D |
|
Service temperature |
−35 °C to +80 °C (short-term +100 °C) |
|
Softening/melting point |
Approx. 190–220 °C |
|
Decomposition temperature |
>250 °C |
|
Auto-ignition temperature |
Approx. 400 °C |
|
Solubility |
Insoluble in water; swells in strongly polar solvents (DMF, NMP) |
|
Abrasion resistance |
Excellent (highly polar ester segments); approx. 10× that of PVC |
|
Oil resistance |
Excellent (low volume change per ASTM D471 reference oils) |
|
Hydrolysis resistance |
Moderate - depends on polycarbodiimide stabilization; slow hydrolysis in warm-humid service |
|
Surface resistance |
Standard grade >10¹² Ω; conductive grade 906S-X: 10³–10⁶ Ω |
Section 10 - Stability and Reactivity
Stability: Chemically and dimensionally stable at ambient temperature and pressure; ester bonds hydrolyze slowly in warm-humid environments, retarded by the polycarbodiimide stabilizer.
Conditions to avoid: Sustained heat >190 °C, open flame, prolonged direct UV exposure, long-term warm-humid storage, high-energy sparks (non-conductive grades).
Incompatible materials: Strong oxidizers, concentrated nitric acid, concentrated sulfuric acid, strong bases (saponify ester bonds).
Hazardous decomposition products: CO, CO₂, NOx, HCN (incomplete combustion), aldehydes.
Polymerization hazard: None (finished high polymer; no reactive residual monomers).
Section 11 - Toxicological Information
No acute toxicity classification is available for the finished TPU article (rat oral LD₅₀ >2000 mg/kg by analogy with similar polymers); no classification for skin sensitization, carcinogenicity or reproductive toxicity. HCN in thermal-decomposition fumes is the principal toxicological risk. No full toxicological testing has been performed on this article.
Section 12 - Ecological Information
Not readily biodegradable; polyester segments can be slowly hydrolyzed by microorganisms (esterase activity) in warm-humid soil/compost, yet the article remains persistent waste.
Incomplete combustion generates CO₂; recycling is recommended (TPU can be mechanically and chemically recycled).
Section 13 - Disposal Considerations
Preferably send to TPU recyclers for material recovery; dispose of waste offcuts as general industrial solid waste (non-hazardous) via licensed contractors.
Do not mix with household waste or burn in the open.
Section 14 - Transport Information
UN number: None (non-dangerous goods); transport marking: general cargo.
Packaging: Carton/woven-bag coils; protect from sharp objects, direct sunshine and rain; keep dry in transit.
Sea/air freight: Not regulated by IMO or IATA.
Section 15 - Regulatory Information
Regulations on the Safety Management of Hazardous Chemicals (State Council Decree No. 645) - not applicable to this article.
GB/T 16483-2008 and GB/T 17519-2013 (SDS preparation standards).
Law of the PRC on the Prevention and Control of Environmental Pollution by Solid Waste (disposal).
Export to the EU: REACH (SVHC) declarations; food-contact uses require food-grade grades assessed to GB 4806.7-2016 / (EU) No 10/2011.
Antistatic applications (906S-X) should be assessed against GB 12158 (General guideline for preventing electrostatic accidents) and site grounding requirements.
Section 16 - Other Information
This SDS is based on current knowledge and a typical formulation; batch variations are governed by the officially issued version; review cycle: 24 months.
Users should verify suitability for their own application (especially warm-humid environments and static-grounding requirements); this document does not constitute a warranty of quality.
Revision record: Version A/1 corrects the base-resin classification - 906S is a polyester-type (ESTER PU) polyurethane, not a polyether type. Accordingly, stabilizer dosage, density, service temperature, storage conditions and hydrolysis-related clauses have been revised. Holders of version A/0 should refer to this version.
Abbreviations: TPU = thermoplastic polyurethane; PBA = poly(butylene adipate) glycol; PEA = poly(ethylene adipate) glycol; MDI = 4,4'-diphenylmethane diisocyanate; BDO = 1,4-butanediol.

